Last updated on August 14th, 2022 at 01:27 pm
One of the life luxuries we all have taken for granted over time is having ice cubes when you need them.
Having a side-by-side refrigerator is a plus, but being unable to get iced cold water on a sunny day can be disheartening.
Sometimes, all that is required to make the ice maker work again is pressing a few reset buttons and other simple procedures.
This does not require the presence of the manufacturer or a technician.
Kenmore ice maker might not work due to a lot of reasons. Different factors such as faults in the ice maker switch and the water inlet valve can cause this. Also, these problems vary depending on the model of the ice dispenser and the operating techniques. However, you can conduct a little investigation to solve the problem.
Why Is My Kenmore Elite Refrigerator Not Making Ice?
A Kenmore elite refrigerator may not make ice, leaving you questioning whether you are operating it rightly or wrongly.
Before you conclude that your refrigerator has defects, below are some factors that may cause your refrigerator not to make ice:
#1. Ice Maker Switch
If the refrigerator is not producing ice, the first thing to check is the ice maker switch. Unfortunately, the controller can get turned off accidentally during operation.
When the button is off, melting occurs, and the water returns to the reservoir. This can make your Kenmore ice maker not make ice.
#2. Water Inlet Valve
When activated, the water inlet valve controls the release of water from the supply and sends it through the refrigerator’s ice maker and water dispenser.
However, the water inlet valve can be clogged with impurities from the water supply, blocking water flow.
In addition, running hard water through the reserve can also give this same effect.
This can lead to the valve malfunctioning and ultimately leads to the Kenmore elite refrigerator stopping making ice.
#3. Temperature Setting
The production of ice by the refrigerator depends on the temperature of the fridge. Therefore, different temperatures are recommended for other parts of the refrigerator.
For example, the Kenmore ice maker must reach 16 degrees Fahrenheit for a cycle to start, and ice eventually forms at 32 degrees Fahrenheit.
#4. Water Pressure
The principle of pressure operates in a refrigerator. It is applicable in a closed circuit, which enables the condensation and evaporation of fluid to remove heat in a refrigerator.
The water pressure needed to produce ice must be between 40 and 120 pounds per square inch.
Pressure below the value indicated above could lead to the production of tiny cubes or no ice at all.
Kenmore Refrigerator Not Making Ice But Water Works?
When your Kenmore refrigerator is not producing ice and the water dispenser is working correctly, it is typical of a clog somewhere.
The fact that the waterworks show that an individual part is defective.
This problem can mostly be traced to the Ice maker assembly. One of many components of the ice maker assembly might be having defects.
Susceptibility to failure of any of these components can be due to consistent usage over time and improper methods of operations.
The ice maker assembly of a refrigerator consists of several parts such as:
#1. Control Module Motor
The control module motor consists of a mold thermostat that measures the temperature of the ice tray.
Once the ideal temperature for producing ice has been reached, the thermostat indicates an indication.
Then the user should remove the ice from the tray and refill it with water to allow the cycle to begin again.
#2. Water Valve
A defective water valve can hinder sufficient water delivery into the system. Also, this can lead to a decrease in the water level needed to produce the ice.
Adjusting or replacing the water valve can be a solution to many of the problems being faced by the user.
#3. Thermostat and Mold Heater
A thermostat is a device used to measure the temperature inside the refrigerator. If the thermostat is faulty, it can give wrong temperature figures and eventually lead to the ice maker not working.
Therefore, it is of utmost importance to know that you should set the temperature of a refrigerator between 0 degrees Fahrenheit and 5 degrees Fahrenheit.
#4. Ice Mold
The front section of the refrigerator has an ice tray. The motor inside this section controls the ejector arm, essential for ejecting the ice cubes.
The ejector arm, which works with the refrigerator, rotates to allow ice cubes to fall into the ice tray.
Therefore, once there is a defect in this section, there will be no production of the ice cubes.
Kenmore Side by Side Ice Dispenser Not Working?
Apart from the fact that this indicates that an ice cube has caused an obstruction, there are several other reasons why your ice dispenser is not working.
For example, refrigerators consist of auger motors that check for ice clumps. If these auger motors are not working correctly, the ice dispensers will not work.
Also, the dispenser control board controls the activities of the ice dispenser. The primary function of the control board is to ensure ice and water are not produced if the door of the freezer is opened.
If a single part of the whole control stops working, the ice dispenser will not work.
The components of the dispenser control board are:
- Dispenser switch
- Dispenser actuator
- Dispenser door motor
- Solenoid
- Ice bucket auger
Why Is My Kenmore Ice Maker Blinking Light?
The light modes on the Kenmore elite refrigerator are meant to inform you about something that is going on in the fridge.
This is one of the significant ways to detect if something is wrong with the ice maker.
A Kenmore ice maker with the red light blinking continuously could be due to an issue with the sensor or the water filter.
This can lead to the refrigerator ice maker not making ice.
Also, when the ice maker is defective, the green light flashes to notify the user that the ice maker needs replacement.
How Do I Reset My Kenmore Elite Ice Maker?
The reset button of the ice maker is located on the front panel of the refrigerator. A simple press on the button will reset the ice maker.
There is a need for paper clips to push the buttonholes, especially if it has a tiny entrance. The power cords of the refrigerator should be unplugged before doing this.
After the procedure, you can plug back the power cords and check if the ice maker is now working.
Also, you can reset your ice maker by simply using the on/off button on the front panel. Then, unplug and turn off the refrigerator for 5minutes, plug back in and switch it on.
You can now check if the ice maker is currently working.
Ultimately, adjusting the feeler arm of the ice maker can give you the solution you have been looking for.
The metallic or plastic rod at the side of the Kenmore ice maker stops it from making too much ice.
The feeler arm moves up and down, following the level of ice present in your ice maker. If your feeler arm is stuck, there will be no ice production.
You will need to push it down to continue ice production.
Conclusion
Your Kenmore ice maker might not work due to a variety of reasons. The reason can be a defect in an individual or a collective part.
This can cause cessation in the production of ice or production of hollow and tiny cubes of ice.
Rather than seeking a quick replacement, a user can perform some simple procedures and adjustments.