KitchenAid Dryer Thermal Fuse Location? (Explained)

Your home appliances are an investment, and it is only natural that you would like to safeguard them and ensure that they continue to perform at their best for the most extended period.

Some appliances, however, are equipped with a self-protection mechanism.

This device is known as a dryer thermal fuse, and You can find it in dryers, microwave ovens, and even certain dishwashers and refrigerators.

This anti-overheating mechanism guards the appliance’s motor and other delicate parts against damage. In addition, the thermal fuse is made to expand or “blow,” disconnecting the voltage.

This prevents electricity from reaching the motor to avoid overheating.

The KitchenAid dryer thermal fuse location is on the dryer’s exhaust duct fitted with thermal fuses to prevent it from overheating. To access the fuse, you must often remove the rear panel of a dryer. Before identifying and fixing the fuse, You or a professional must also remove the dryer’s electricity.

Where Is The Thermal Fuse Located On a KitchenAid Dryer?

The thermal fuse can be found on the exhaust duct of a KitchenAid dryer.

This thermal fuse component is just one or two inches long and should be; however, the position of the exhaust duct itself may change depending on your model.

The thermal fuse aims to keep dryers from catching fire by sensing when the drum becomes too hot and tripping.

Even though a thermal fuse is a one-time-use part, it is affordable and simple to repair. Consequently, the dryer will come to a stop if it fails.

Remember that because the thermal fuse is a component of the dryer’s safety system, Do should not use the dryer again until the thermal fuse has been replaced.

It’s time to determine if it’s blown after discovering it.

How Do I Know If My Thermal Fuse Is Blown?

Knowing where to look is just half the battle when identifying a blown or damaged thermal fuse. The following basic steps explain the process:

  • Unplug your dryer and make sure it’s not still using gas or electricity before you do anything else.
  • As previously said, locate the thermal fuse.
  • Remove the wires from the thermal fuse and disconnect them.
  • Use a multimeter to check the fuse.
  • If your multimeter’s needle doesn’t move, you’ve got a blown thermal fuse.

#1. Clear The Vents If Necessary

To ensure that any replacement thermal fuse you fix doesn’t blow after a short time of dryer operation, you should clean the dryer’s venting once you’ve confirmed that a blown thermal fuse causes the problem.

The accumulation of lint in the dryer’s exhaust vent is the most common cause of thermal fuses blowing.

Once yearly, disconnect the appliance’s venting from the appliance’s back and use a vent cleaner to remove lint and other debris.

In addition, you can use a vacuum cleaner to frequently remove dirt from the dryer’s lint filter and the filter housing itself.

Additional methods are available for determining whether or not the vents are blocked. While this step may appear unnecessary, it’s a perfect place to start.

  • In times of excessive dryness during a regular dry cycle, if you notice that your garments are not getting completely dry, this may be one of the earliest indications that your dryer vent is clogged.
  • Burning Smell. Have you noticed that your dryer emits a smell of something being burned anytime you have a load running in it?
  • A sizzling exterior.
  • Large Amounts of Lint

Will The Dryer Run If The Thermal Fuse Is Blown?

If your dryer won’t start, operate, or heat up, the most likely cause is a blown thermal fuse.

Once a thermal fuse in a dryer has blown, You should replace it with a new fuse for the dryer to be operational again.

This is in contrast to a high-limit thermostat, which You can reset directly. However, could you take out the thermal fuse and test it before buying a new one?

The thermal fuse is commonly found on the blower housing or close to the heating element in electric dryers. In addition, there is a thermal fuse located near the burner in gas versions.

In some dryers, the fuse is accessible by simply removing the appliance’s back panel or a lower access panel on the front.

Many need you to remove the appliance to reach the fuse when it comes to dryers. This includes the top panel, the front panel, a bulkhead, and the appliance’s drum.

That is the most difficult aspect. Remove the screws holding it in place and unplug the power cords from the fuse’s terminals to remove the fuse.

How Do I Reset My KitchenAid Dryer?

  • The simplest solution is to press the reset button. To access it, locate it by looking for a button or a light switch. Simply pressing this button will force the KitchenAid dryer to restart.
  • The dryer can also be reset by turning it off and removing the power cord. Before disconnecting the dryer and turning it on, let it cool for 10 minutes.
  • A KitchenAid dryer will not operate if the circuit breaker is tripped. To reset your dryer in this case, you may turn the breaker off and then back on again.

A simple press of the reset button can solve many issues.

However, it cannot solve all of the dryer’s problems. If resetting your KitchenAid Dryer doesn’t work, you may do a few other things.

  • First, check to see if the dryer is properly wired to an electrical outlet. Do a test to confirm that the plug is properly inserted into the outlet. Replace the plugs. You never know what’s going on with the outlet near the dryer.
  • Has the plug been thoroughly inspected? A blown fuse or loose wiring might also prohibit the KitchenAid dryer from receiving the electricity it needs to operate.
  • Check the door. You can’t get the dryer to function unless you firmly close the door. Check the door switch if the dryer won’t start even when the door is shut tightly. The dryer’s functionality will be affected if the dryer door switch is defective.
  • Verify that the circuit breakers and fuses are in good working order. It would help if you replaced every blown fuse.
  • Vents and traps should be cleaned. Overheating might happen if they become clogged.
  • Even though it’s unusual, the start switch might also go bad. The start switch should be examined if you keep pressing it and nothing happens.

Resetting the dryer will remedy a wide variety of fundamental issues and complications. You may find this in several cart KitchenAid dryers.

However, it’s not just a KitchenAid approach; Even if your appliance is gotten from the OEM manufacturer order, there are tons of ways you can reset your dryer thermal fuse pack.

Electronic gadgets are prone to malfunctioning at any time; however, this is especially true in the event of a power cut.

Conclusion

A dryer consists of a drum, a motor, pulleys, and hot air, all of which work together. Dryers frequently malfunction.

There are certain difficulties with these appliances that can be solved with a few easy steps.

Please don’t rush to hire a professional to fix your KitchenAid dryer when you can easily reset it and get it working again.

Why Trust Our Information

At Homeguideinfo.com, we are dedicated to delivering precise and trustworthy information. Our content is meticulously developed and validated by a panel of Expert Contributors, adhering to strict Editorial Guidelines. Our commitment is to ensure that you receive thoroughly researched and expertly crafted information.