Last updated on August 14th, 2022 at 01:27 pm
A washing machine is an essential piece of equipment that helps make laundry easier. The Maytag Centennial Washer is reliable and efficient at cleaning.
In addition, the commercial washer technology assures long-lasting durability. This is a large-capacity washer that can handle just about anything.
However, as many qualities as a machine has, it can develop a defect for a specific reason. As a result, the Washer may not work or start, which will affect productivity.
The washer will not turn on if you do not correctly connect it to an electrical outlet or if it is not working. Another reason could be a faulty lid switch or main controls, which could have stopped working for some reason. Additionally, overheating can also be one of the reasons why the machine refuses to start.
Maytag Centennial Won’t Start Wash Cycle?
The machine will not start the wash cycle because you may have selected the wrong cycle. Check the wash cycle indicator and adjust appropriately.
The lid switch is responsible for detecting whether the washer lid is closed. The cover must be closed for the washer to start a cycle.
So when a top load washer like the Maytag doesn’t trigger the wash cycle, you need to lock the lid properly. Another reason could be a broken lid switch or lock assembly.
There may also be some problems with the washer activator and tub sensor that prevent the machine from starting the wash cycle.
Washer sensor problems usually appear in fault codes like F7E1, F7E5, or F7E7. Pay attention to washer error codes that indicate that the washer activator may be faulty.
To find out the washer error code, you may have to go through some procedures like;
- Ensure the machine is in standby mode. Then, push the START/CANCEL button for 3 seconds, turning off every activity.
- Rotate the wheel selector knob anticlockwise to clear the sequence.
- Rotate wheel selector knob anticlockwise. There should be a full rotation, and the control panel beeps.
- Turn the cycle selector knob one click towards the clockwise direction and wait for half a second.
- Repeat the step above two more times.
- Rotate the knob anticlockwise one click and wait 1/2 second.
- Repeat in the clockwise direction and wait 1/2 second.
- You are now in diagnosis. Turn on until only the “Done” LED lights; push start.
- Turn the dial clockwise with one click, and the error code will display as an LED with a progress line.
Note: After reset, actions from “two” to “six” must be completed within 6 seconds.
Why Is My Maytag Washer Not Starting?
First, make sure the machine is plugged in, and the power cord is connected to a live outlet. Then, you can test the outlet with another three-pronged device or a power tester.
Next, check the power button; you might have forgotten to switch on the machine.
Additionally, overheating used by running multiple loads one after the other may prevent the machine from starting.
The best way to solve this is to turn off the device and give it a few hours to cool down, then try again.
Also, a machine model that uses a mechanical timer knob will not run until it is filled with water to the selected level.
In addition, the door interlock and control board may prevent the driver washer from starting.
If your washer is not starting, it could be due to any of these reasons. You can fix some yourself or call a professional to correct the problem.
It depends on the type of defect the washer is developing.
Is There a Reset Button on a Maytag Washer?
No, Maytag washers don’t have a reset button. The machine doesn’t come with a reset button; you will have to repair it and create a method to reset it.
You can also unplug from the outlet for a minute and plug it back in to activate the reset.
Alternatively, you can also use the Power button to stop the current cycle. Select a new cycle and press Start/Pause.
How Do You Reset a Centennial Washer?
The easiest way to reset a Maytag washer is to unplug the washer from the power outlet for a minute. Then, plug it back in to reset it.
Programmable washing machines may have a reset function or position in place of a button. Similarly, you can select “Power off” and then Cancel.
Next, change the wash cycle by pressing the appropriate button. Then press “Start/Stop” to reset.
Another method to reset the machine is unplugging the washer from the electrical outlet for a minute. Then, plug the washer back on and lift and lower the lid six times.
You have 30 seconds to start raising and lowering the cap. The motor is now reset and ready for you to start a cycle.
Maytag Centennial Washer Won’t Drain or Spin?
Common reasons a Maytag Centennial washer won’t drain or spin are uneven loads or jammed clothes. Try to arrange the clothes properly and redistribute the load evenly.
You can also remove some of the clothes and run the spin cycle on the washer again.
Also, something could be stuck in the machine drain hose, or the pump is faulty. Unplug the washer and clean the house to remove any residue trapped in it.
The drain hose can also be twisted or coiled. Check the back of the washer and straighten a bent hose.
At the same time, always clean the inside and outside of the machine at least once a month. Use a regular cycle or sensory cycle to wash the machine’s interior.
Remove any dirt or detergent residue from the dispenser or drawer openings.
Some problems can be solved independently, while some may require a professional. Here are some reasons why a Maytag Centennial washer won’t drain or spin.
#1. Faulty Motor Coupling
The motor coupling connects the motor and transmission, allowing the washer drum to function. If it breaks, the washer’s spin cycle will not work.
If the washer is constantly under heavy loads, the motor coupling may soon fail and be permanently damaged. If it is damaged, you will need to replace it.
#2. Lid Switch
The lid triggers the switch when the plastic tub on the top is closed. Check the plastic tub and make sure there is no damage to the tub.
Hear a clicking sound when closing the lid. If the lid switch is broken you will not hear any sound. A professional would need to replace it.
#3. Faulty Bearing System
There are springs on the rear drum of the washer so that the inner tube can move freely. If a Maytag washer stops a spin cycle, it must be one of the parts to check.
Besides, the machine will make a lot of noise because of the broken bearing. You need to fix it ASAP.
#4. Driver belt
The machine will not spin if the driver’s belt is broken, damaged, or loose. However, when the engine turns and makes a loud noise, you should pay attention to it.
#5. Worn Clutch
If the clutch is worn out, the washer cannot spin. Unfortunately, there is no repair solution for a worn-out clutch. The only way is to change it completely.
#6. Worn Out Transmission
The washer transmission has its components. When the part fails, the washing machine will not spin. As a result, the transmission may wear out over time.
You should check all other components to ensure they are correctly installed before you resolve to replace the transmission.
#7. Damaged Magnet on Rotor
The washer will not spin if the rotor magnets are damaged. This is because the rotor creates a strong electromagnetic field that interacts with the stator to rotate the tub; you cannot repair it.
Therefore, if it is found to be damaged after inspection, you need to replace the rotor. You should always seek a professional opinion before making any decision.
Conclusion
The Maytag Centennial washer will develop a fault like every other appliance. Therefore, the best thing to do is always to be ready.
For example, the machine may not start due to an incorrect power connection, a trip in the wire connection, improper lid placement, improper adjustment of the controls knob, etc.
Whatever the reason, do well to get it checked out or call a professional to have it checked if you’re still confused.