In the world of dishwashers, encountering one or two faults is normal. Whirlpool dishwasher is one of the best reliable dishwashers, but it’s not exempt from having issues.
Issues like the Whirlpool Dishwasher stopping after a few minutes or seconds are typical. There are, however, several causes for this problem.
The Whirlpool Dishwasher has features like a Quick wash cycle and 1-hour cycle. If your Dishwasher doesn’t run a complete cycle, there’s a problem.
This article will enlighten you on the possible causes and solutions to fixing your whirlpool dishwasher.
In certain instances, your Whirlpool Dishwasher can stop after a few minutes or seconds. This fault can result from broken or damaged parts of the appliance. Besides, incorrect settings on the dishwasher can also cause it to stop at intervals without running a complete cycle.
Why Does Whirlpool Dishwasher Stop After A Few Minutes?
There’s usually an error message whenever your Whirlpool Dishwasher stops after a few minutes. Depending on the version and functioning issue, you can get any error messages below.
#1. Eight Flashes of “Cancel light” After Your Whirlpool Dishwasher Stops
This error message can be confusing, especially if you’ve never experienced it. You might think your Whirlpool Dishwasher is resetting until it shuts off.
The filled water might even drain, which can leave you bewildered. Still, you can try to fix this yourself.
The eight flashes after your Whirlpool Dishwasher stops depict a filling issue. You can solve this issue by erasing stored errors on your Dishwasher.
Follow the steps below.
- Check for the program button option on your Whirlpool Dishwasher.
- Press and hold it, and about four LEDs will show.
- With your finger still on the program button, double-tap the Start button.
- Then, the second LED from the left will make an indication.
- Release the program button, and you’ll find the Stored errors option.
- You might see the ECO light flashing, don’t worry about it.
Afterward, press the program button again and select erase error.
#2. Whirlpool Dishwasher Making Sounds, Filled Water Draining Out, And No Cycle
It’s probably a motor fault resulting in your Whirlpool Dishwasher stopping a wash cycle, making noises, and draining water.
You can try a Whirlpool dishwasher reset first before concluding it’s a motor issue. You can do the Whirlpool Dishwasher reset by following the below steps.
- Switch on your Whirlpool Dishwasher and select “Glasses 40°C Cycle”.
- Switch off your Dishwasher and long-press the start button.
- Turn on the Dishwasher after and hold till the start button flashes.
- Let go and gently press the start button again.
Your Whirlpool Dishwasher should then run a test cycle.
However, if you get another error message as five flashes with pauses in between, your Whirlpool has a Motor issue.
#3. Five Flashes With Pauses In Between
Five flashes depict a motor issue, and most times, you might have to install another pump motor assembly.
Still, you can use the below troubleshooting tips.
- Dismantle your Whirlpool dishwasher by removing the first inspection cover beneath the door and the bottom base.
- Pull out the motor assembly and check for dirt & debris.
- Ensure that it’s clear and the hoses are also free of dirt.
- Fit in the pump motor assembly and start the wash cycle. If the issue persists, you’ll have to install a new pump motor assembly.
Why Does Whirlpool Dishwasher Shut off after a few seconds?
It can be frustrating when your Whirlpool Dishwasher Stops after a few seconds without starting a wash cycle. I mean, the power indicator is on; what could be wrong?
This situation where your Whirlpool dishwasher shuts off after a few seconds is similar to when it stops after a few minutes. There are diverse causes of this issue.
Some of them include the causes listed above, like old or non-functioning pump motor assembly and irregular Dishwasher settings.
However, other reasons can be loose door latch, broken thermal fuse, damaged electronic control board, etc.
#1. Loose Door Latch
The door latches on your whirlpool dishwasher keys to prevent water from spilling during wash cycles.
But if your Dishwasher beeps continuously and stops after a few seconds, then the door latch is loose or broken.
#2. Broken Thermal Fuse
When your Whirlpool Dishwasher gets too hot, the thermal fuse acts as a safety button to stop the motor and circuit board.
Hence, temperature irregularities can occur if the thermal fuse is faulty, halting the dishwasher during cycles.
#3. Damaged Electronic Control Board
Another reason why Whirlpool Dishwashers shut off after a few seconds is the damaged electronic control board.
The control board is meant to regulate the internal functioning of your Dishwasher.
Moreover, it can cause erratic functioning, like the dishwasher stopping after a few seconds if it gets damaged.
Why won’t My Whirlpool Dishwasher run a cycle?
Usually, your whirlpool dishwasher should start a wash cycle when switched on. But if it doesn’t start a cycle or stops mid-cycle, it could be either one of the following causes.
#1. Activated Control Lock
To make a complete cycle, you must deactivate all the controls for your Whirlpool Dishwasher.
Hence, you should check your control pick if your Dishwasher Stops mid-cycle. If it’s activated, you can deactivate it by long-pressing the lock switch for about four seconds.
#2. Activated Sleep mode
Activating the sleep mode on your dishwasher can also be why your appliance isn’t completing a cycle.
You can deactivate it by pressing the start or resume button or opening and closing the door.
#3. Enabled Delay Wash
Another reason why your Whirlpool Dishwasher might not complete a cycle is the enabled delay wash option.
However, the delay wash option should be disabled to activate the complete wash cycle.
Depending on your model, press either Cancel or Drain to disable the delay wash. After, press the start or resume button to continue the cycle.
#4. Irregular Water Supply
When your water supply is cut off, it can cause your whirlpool dishwasher to stop mid-cycle. You can activate it by checking your appliance installation manual.
How do I run a Diagnostic on my Whirlpool Dishwasher?
Running a diagnostic mode is the best option when things go wrong on your Whirlpool Dishwasher.
The diagnostic model helps identify the error and enables you to figure out the solutions to the issues.
The flashing lights on the display will indicate the faults in your Dishwasher.
Moreover, if you’re using a model with no digital panel, the clean light button will illuminate the function code.
Then, there’ll be a pause for about two seconds before the error code flashes.
Count the number of times the clean light flashes to know your Whirlpool Dishwasher’s fault.
Follow the steps below to run the diagnostic mode on your whirlpool dishwasher.
- Switch on your Whirlpool Dishwasher
- Select the “Rinse Cycle” button
- Switch off the Dishwasher
- Press and hold the start button
- Let go of the button when the lights start flashing.
How long does a Whirlpool Dishwasher Diagnostic take?
While running the diagnostic mode on your whirlpool dishwasher, several parts of the appliance are checked to ensure adequate functioning.
Some components are the water inlet valve, the wash pump heater, the drain pump, the high wash, and the pump dispenser.
Thus, the diagnostic mode will run for about 2-3 minutes.
Summary
Whirlpool Dishwasher is one of the popular Dishwashers you can get for your household. The appliance is quite reliable and can serve its purpose efficiently.
But, more so, it can also develop faults. A common fault is the Whirlpool dishwasher stopping after a few minutes or seconds.
This fault is due to several causes highlighted above. Also, your whirlpool dishwasher stopping mid-cycle can be frustrating.
This article tackled the reasons for this fault, and possible solutions are provided.
Endeavor to read through and learn how to run the diagnostic mode for troubleshooting tips on your Whirlpool Dishwasher.
