Asko dishwashers are known for their build, quality, performance, and long life span.
Asko manufactures both Stainless Steel Dishwashers and Panel Ready Dishwashers.
The panel-ready design is best if you want your dishwasher to blend in with the cabinetry in the kitchen.
The interior of any Asko dishwasher model contains a lot of steel.
The fact that they are dishwashers made of steel makes them challenging.
The steel-built dishwasher has an advantage over other dishwashers because you can use them for a long time.
All these models come with the same door handle. Although the machine is reliable, the dishwasher can develop defects affecting its operation.
If the buttons on your control board are stuck or the touchpad is damaged, the Asko dishwasher Start/Stop button will not work. If you don’t correctly plug the appliance in, the buttons won’t work. When the child lock is activated, the buttons won’t also work. It would prevent the buttons from responding.
Why Is Asko Dishwasher Start/Stop Button Not Working?
First, you should check if the dishwasher is plugged in. If you find that your dishwasher buttons are not working correctly, the dishwasher may not be plugged in.
Check the dishwasher and make sure it is connected to an electrical outlet.
If it still doesn’t start after plugging in the dishwasher, you may need to check the circuit breaker. First, make sure the switch is in the correct position.
After this, the dishwasher will work properly. Next, make sure the dishwasher is also connected to the water supply. Otherwise, it still won’t turn on.
There are also some other reasons why the device won’t start, outlined below.
#1. Start/Stop Button Stuck
A common cause of your buttons getting stuck is too much dirt. Dirt, grease, and oil can build up, affecting the proper functioning of the switch.
It’s widespread for these buttons to get stuck, especially if your dishwasher has a top control panel.
Suppose the button is stuck in place. You can use an ammonia-based cleaner to remove the switch.
The ammonia-based cleaner is perfect for breaking down food, dust, debris, and grease that can clog the dishwasher buttons.
When using ammonia for cleaning, you should always wear gloves and protective goggles to protect yourself from health risks.
You should also avoid mixing ammonia with bleach.
This can release a toxic solution that is dangerous to your health. You can get burned and damage your respiratory system.
#2. Electrical Wiring Problem
Another reason your buttons may get stuck could be due to a problem with the electrical wiring. Most controls on a dishwasher use electrical systems.
The key may malfunction due to a wiring problem. If it does, you will need to call an electrician who can fix it.
#3. Child Lock
There are plenty of dishwashers these days that come with a child lock. However, if the child lock is on, the rest of the buttons may not work.
The purpose of the Child Lock is to prevent children from accidentally changing commands on your wash cycle.
Therefore, you must remove the child lock for the rest of the buttons to work.
#4. Trap and Filter Assembly System
Additionally, there could have been a malfunction in the trap and filter assembly system. The trap and filter system can also cause problems with the dishwasher buttons.
Also, the trap at the bottom of the dishwasher is clogged with debris, which can cause the water pump to stop working.
If the water pump isn’t working correctly, the rest of the dishwasher won’t work.
You should always clean the trap and filter system and other parts. But, first, you should look at the manual to see how to do it on your dishwasher.
Once the trap and filter system is cleaned, the dishwasher should start working again.
In addition, you may also need to reset the control panel if the buttons are still not working after this.
How to Make Dishwasher Buttons Work?
After figuring out what the problem could be, the following process is to find a solution.
You should give it due attention to ensure the machine’s working and avoid causing more problems.
Here are solutions to common issues that can affect the dishwasher.
#1. Unplug the Dishwasher and Plug It in Again
The first thing to do is check if the machine is properly plugged in and the outlet is working.
Begin by unplugging your dishwasher, then look at the circuit breaker to see if the switch is in the correct position.
Next, plug the dishwasher in again. Give the dishwasher a few minutes to boot up and start working.
Also, make sure the water supply is connected to the dishwasher. Next, test the dishwasher to see if it is working.
Unplugging the dishwasher is the perfect way to remove any stuck commands from your system.
#2. Turn off Child Lock
Take a look at the dishwasher control panel and see if it has a child lock button. If the Child Lock button is lit, this is an indication that Child Lock is activated.
So, you may have to press it for three seconds to release the child lock button. You can also hold down the Start button for a few seconds.
This will clear the rest of the buttons.
#3. Clean the Trap and Filter System
Always make sure you clean the trap and filter system. This could also cause a problem with the dishwasher button.
The flashing of the button indicates that the trap is entirely complete.
First, you need to remove the bottom rack of the dishwasher. There is usually a cap that you need to turn counterclockwise to take the assembly out of the dishwasher.
Then, remove any debris present before returning the system to the dishwasher. This allows the buttons to work again.
#4. Reset the Control Panel on the Dishwasher
Lastly, you should reset the control panel on the bottom of the dishwasher. First, disconnect the dishwasher from the power source.
Then removed the control panel from the door panel. Always remember to disconnect all wires from the control panel during this process.
If the wires are intact, you can reconnect them. If they are damaged, you may need to replace them.
Put the control panel back in the dishwasher after the cables are in the correct position.
This can be dangerous, so you should call an electrician if you don’t understand the process.
If the dishwasher is still not working after trying all the above solutions, you need to contact a professional who can help you.
Asko Dishwasher Will Not Work after Fixing Start/Stop Button?
After the start/stop button has gone through working, the dishwasher may still refuse to work.
This can result in defective machine parts, which are essential for the machine’s proper functioning.
Some of these parts are outlined below to understand them properly.
#1. Thermal Fuse
The thermal fuse is responsible for turning off the dishwasher’s power. If the thermal fuse blows, the dishwasher will not start.
In determining whether this fuse is faulty, test for continuity using a multimeter. If the thermal fuse does not have continuity, you will need to replace it.
#2. Door Latch
The door latch ensures that the dishwasher door closes appropriately to prevent water leaks. It also has a door latch switch that powers the dishwasher controls.
If the door is not fitted correctly, the door latch switch will prevent the machine from working.
Locate the door switch on the dishwasher door and make sure both buttons are mechanically activated when the door is closed.
You can use a multimeter to check the door latch switch for continuity, but always make sure the dishwasher’s power is turned off.
If the door latch is broken, it will need to be replaced.
#3. Main Control Board
The main control board works by powering almost every component of the dishwasher.
If there is a problem with the main control board, it may not be sending voltage to the dishwasher.
In this case, the dishwasher will not start. Make sure you check the other parts for defects before you decide to replace the main control board.
#4. TouchPad
If the touchpad is faulty, some of its buttons will not respond. Likewise, if the touchpad isn’t working correctly, you’ll need to replace it.
Some touchpads are sold separately from the control panel, while others require you to purchase the touchpad and control panel together.
If you cannot replace the touchpad individually, you will need to replace both the touchpad and the control panel.
#5. Timer
The timer determines how much power needs to flow through the various components.
For example, the drain pump, heating circuit, and water inlet valve in a dishwasher receive power from a timer or electronic control during the wash cycle.
If these parts do not get the required energy, they will not function properly.
After ensuring the door is engaged correctly, turn off the power and check the timer or electronic controls with a multimeter.
If the timer isn’t working correctly, it may not be sending voltage to the dishwasher.
Check for other faulty parts before replacing the timer, as timers are often misdiagnosed.
Conclusion
The Asko dishwasher Start/Stop button may not work for all of the reasons given, but it is essential to check if the appliance is plugged in correctly before concluding the fault.
Handling Asko dishwasher troubleshooting is not tricky, but if there are too many errors to run or it seems complicated. You should contact a professional for help.