Dishwashers save time and energy and help make dishwashing an exciting chore while giving your dishes that sparkling look.
They have become widely used and irreplaceable, as most households can not do without them.
However, because it is a machine, it will occasionally develop problems. One of which is your Frigidaire dishwasher getting stuck in heat dry mode.
A Frigidaire dishwasher can get stuck in the heat dry mode due to several reasons such as:
- A tripped fuse or circuit breaker
- A faulty thermostat
- A defective timer
- A malfunctioning main control board
- A failed heating element
Why is My Frigidaire Dishwasher Locked On Heat Dry?
When your dishwasher gets stuck during a cycle, it is enough for you to raise eyebrows over what the problem is with your appliance.
This article will outline all the possible reasons why your dishwasher often locks on dry heat mode.
#1. Faulty Circuit Breaker
The circuit breaker is responsible for protecting the dishwasher when there is an electrical problem or an overload.
However, when the circuit breaker or fuse is tripped, the dishwasher runs erratically, causing it to get locked in the dryer heat mode.
To reset the dishwasher when this happens, switch off the breaker for about 5 minutes.
#2. Damaged Thermostat
A defective thermostat is likely to cause the dishwasher to get stuck in a drying mode. The thermostat controls the temperature of the dryers on the dishwashers.
Nevertheless, high-ranking appliances repair agencies such as Repair Clinic have confirmed that when the thermostat troubleshoots, the drying cycle will not start or end as expected because the thermostat will incorrectly detect the start and end of a cycle.
Unfortunately, unlike other parts of the dishwasher, you can not repair the thermostat, so it has to be replaced.
#3. Broken Timer
The timer on the dishwasher is responsible for disturbing electricity to different parts of the device as much as each cycle needs.
The timer is one of the things you should look out for when your dishwasher gets stuck on dry heat.
Unfortunately, it is not repairable, so it has to be replaced.
#4. Malfunctioning Main Control Board
No matter how insignificant it may seem when it develops from the control board, any slight fault is capable of resulting in your appliance getting locked in a drying mode.
#5. Faulty Heating Element
The heating element circulates heat. It also heats the water inside the dishwasher.
When it gets faulty, the water will remain warm and will not dry any of the dishes in the cycle. This is why it trips and alters the dry heat cycle.
A faulty heating element should be replaced immediately and not repaired.
How To Turn Off Heat Dry On A Frigidaire Dishwasher?
Frigidaire dishwashers, unlike other brands of dishwashers, have a set of error codes and reset buttons to clear out errors or troubleshoot the appliance.
For instance, the heat dry on the frigidaire dishwasher can be turned off by simply selecting the heat dry button and turning it off, but more than this, you can use two other methods to disable the heat dry on your dishwasher.
They are:
- Error codes
- Resetting the dishwasher
Without further ado, I will quickly explain these methods above and how to effectively use them if your dishwasher is stuck during a dry heat cycle.
Frigidaire Dishwasher Error Codes
Error codes assist you in understanding the issues plaguing your Frigidaire dishwasher.
These codes that pop up on your dishwasher’s display allow you to instantly get a hold of the exact problem and deal precisely with it.
#1. Error Code i60
The problem: A faulty heating element is detected.
The solution: This error code is displayed when there is a fault with the heating system, thermostat, hot water supply, or a faulty control panel.
To clear this error, press and hold the cancel button or turn off the power and disconnect the dishwasher for at least five minutes to allow the error code to clear out.
If it continues, you’ll be left with the option of contacting a professional to fix it up. Still, you can troubleshoot the water heating element.
#2. Error Code iC0
The problem: a faulty electronic control panel system is detected.
The solution: press and hold the cancel button on the dishwasher or turn off the power supply. Leave it off for about five minutes.
The arrows will automatically clear out when you turn it on again.
However, if it does not, you will have to do a troubleshoot on the device or easily fall for the services of a professional to help you fix the problem.
#3. Error Code UO
The problem: this error code is displayed to show that during a circle, the main control board receives the signal from the vent assembly, which is usually close; therefore, when it becomes ajar, this code is likely to display.
Solution: check out the wiring between the main control board and the vent assembly.
The vent assembly is likely to be replaced if you notice that all the wires are connected correctly only if the error continues and shows to replace the main control board.
#4. Error Code hs
The problem: The dishwasher has detected a hall sensor error that connects to the motor.
The solution: examine all the wires between the motor and the main control board.
Replace the motor where necessary. If the error does not show any sign of stopping, replace the main control board.
As I explained above, these error codes have been selected specifically for the possible culprits of a dishwasher getting stuck during a dry heat mode cycle.
They are a few amongst many others.
Resetting The Dishwasher
Resetting your dishwasher helps keep it working at its best and effectively.
To reset the Frigidaire dishwasher, press and hold the cancel button for 3 seconds; this will automatically shut off your dishwasher and reset it.
Wait for 5 minutes, then restart it and improve to a new setting. Finally, fill it with a load to test if the reset worked.
#1. Hold And Press The Dishwasher Cancel Button For 3 Seconds
To reset the dishwasher, locate the cancel button.
The cancel button on your Frigidaire dishwasher is located on the right side by the control panel, press it for 3 seconds, and wait for the light to turn off till it changes color.
This will shut down the dishwasher immediately.
#2. Wait For 5 Minutes Then Switch On The Dishwasher
Turn the power button for 5 to 10 minutes and turn it on again. Finally, press the start button for about a second. This is a reset of a Frigidaire dishwasher.
#3. Switch Off The Circuit Breaker Or Fuse
If the above steps do not turn on the dishwasher, turn off the circuit breaker for 5 minutes.
#4. Restart The Dishwasher
Switch off the circuit breaker and unplug it. Then for a few minutes, allow it to be out of power. Then, turn it on again, and this time, try running a cycle inside.
The Frigidaire dishwasher manual is also an excellent source to consult for steps on how to reset your dishwasher.
Conclusion
A Frigidaire dishwasher is one of the most reliable and durable brands of dishwashers. Nevertheless, as a machine, it will develop some issues.
This article outlined and discussed the possible reasons why a Frigidaire dishwasher gets stuck or locked in a heat drying mode.
Among others, these reasons are a faulty fuse, thermostat, main control board, and a faulty heating element.
